Sealey AK505 Instrukcja Użytkownika Pobierz pdf

Instructions for:

PIPE FLARING KIT

Models:

AK505 & AK506.V2

1.1. GENERAL SAFETY

 WARNING! Ensure Health & Safety, local authority and general workshop practice requirements are adhered to when using this

equipment.

 Familiarise yourself with the application and limitations, as well as the potential hazards, of the kit.

 This kit is suitable for flaring copper, brass or thin walled aluminium pipe. DO NOT use for flaring steel pipe.

 Maintain the kit in good condition (use an authorised service agent).

 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the

warranty.

 Locate the flaring tools in a suitable work area. Keep the area clean and tidy and ensure there is adequate lighting.

 WARNING! Always wear approved eye or face protection when using the flaring tools.

 Keep children and unauthorised persons away from the work area.

 Secure pipe clamp in a vice.

 DO NOT use the kit for any purpose other than for which it is designed.

 DO NOT use the kit if any parts are damaged or missing as this may cause failure and/or personal injury.

 DO NOT allow untrained persons to use the kit.

 DO NOT attempt to flare piping when you are tired or under the influence of alcohol, drugs or intoxicating medication.

 When not in use clean kit components, replace in case and store in a safe, dry, childproof area.

Remember! The safe operation of a vehicle, or other equipment, may well depend on the quality of the flare produced.

Discard any flare which is malformed.

1. SAFETY INSTRUCTIONS

2. CONTENT

3. OPERATING INSTRUCTIONS

Check the content of the kit against the list below. If any item is missing or damaged, contact your supplier immediately.

2.1. AK505 AK506.V2

 •PipeClamp    •PipeClamp

 •FlarePress,45°    •FlarePress,45°

 •FlareDies-3/16”,1/4”,5/16”,3/8”,7/16”,1/2”,5/8” •FlareDies-3/16”,1/4”,5/16”,3/8”,7/16”,1/2”,5/8”

      •PipeCutterwithDe-burringBlade

 WARNING! BeforeusingtheflaringkitensurethatyouhavereadandunderstoodtheSafetyInstructionsinSection1.

3.1.Thepipeendtobeflaredmustbecutcleanandsquareandbede-burred.Usepipecutter supplied in AK506.V2

kit or Sealey model number: AK5051,ifusingkitAK505.

3.2.Mountthepipeclampinavicebytheend‘A’(fig.1).Checkthatthewingnuts‘B’areaccessibleandcanbeturnedandthat

the pipe clamp hole chamfers (and sizes) are uppermost.

3.3.Slackenthewingnuts‘B’andinsertthepreparedendofthetube-withflarenut‘C’(fig.1)fitted-upthrough

the appropriately sized clamp hole. Adjust the protrusionofthepipesothat‘X’(fig.2)isbetween1/8”to3/16”depending

on pipesize-thelargerthepipethegreater‘X’. Tighten wing nuts.

3.4.Placetheappropriatelysizeddieinthepipeendandthenfittheflarepress‘D’(fig.1)ontotheclampandoverthedie.

3.5.Screwdownpress,andthereforedie,untilthe‘single’flareisformed(fig.3).Removepressanddieandcheckthat flare is symmetrically

formed.

3.6.Toproducea‘double’flare,proceedasaboveto3.5.Then remove die and screw press down into‘single’flare.Thiswill

compress topsection(‘E’fig.3)of‘single’flareintobaseofflaretoproducea‘double’flare(fig.4).Again,check that flare is

symmetrically formed.

fig. 1

fig. 2

fig. 3

fig. 4

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH

IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE

THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

AK505 & AK506.V2 1

Podsumowanie treści

Strona 1 - AK505 & AK506.V2

Instructions for: PIPE FLARING KITModels: AK505 & AK506.V21.1. GENERAL SAFETY WARNING! Ensure Health & Safety, local authority and general

Powiązane modele: AK506

Komentarze do niniejszej Instrukcji

Brak uwag

Sealey AK505 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Narzędzia Sealey AK505. Sealey AK505 User Manual Instrukcja obsługi

Podsumowanie treści

Powiązane modele: AK506

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Narzędzia Sealey AK505